Results 1 to 11 of 11
  1. Post 27th December 2018, 8:13 pm
    #1

    Ethernet cat6 only working properly via switch?

    EDIT: seems to be working now. I have no idea why.

    I have 15m of CAT6 running from the router to my PC, but am only getting 1Mbps on speedtest.

    What works as it should 100Mbps
    Router > 15m Cat6 > Netgear 10/1000 switch> 30cm of Cat5e > PC

    What doesn't (well, does but gives 1.5Mbps)
    Router > 15m Cat6 > new Dlink Gigabit switch> 30cm of Cat5e > PC
    Router > 15m Cat6 > PC


    Any idea what's going on here? It's only come to my attention because I have bought a new gigabit switch, and only get 1Mbps on it. So plugged the Cat6 directly into the PC and wouldn't you know it, also only 1Mbps.

    Any ideas?


    (the reason I have the switch is for networking with another PC I sometimes use for work)
    Last edited by Richard7666; 27th December 2018 at 8:54 pm.
    Richard7666
    Richard7666's Avatar
  2. Post 27th December 2018, 8:20 pm
    #2
    Did you attach the plugs to the cable or is it a pre-made cable?
    DW
    DW's Avatar
  3. Post 27th December 2018, 8:35 pm
    #3
    Update: tested it with a laptop (both cat6 direct to laptop, and via new switch which only gives 1.5Mbps on PC) and it works at full speed.

    So wondering if it's something to do with my motherboard's port not liking the Cat6 cable?

    However, I also have a new gigabit switch. I've edited my original post to include another test

    DW wrote:
    Did you attach the plugs to the cable or is it a pre-made cable?
    I got it from the local branch of a large electrical wholesaler. So I'm not sure.
    It's a Dynamix cable, from reading it
    Richard7666
    Richard7666's Avatar
  4. Post 27th December 2018, 8:54 pm
    #4
    aaand it's randomly working now. Slightly over 105Mbps on speedtest (I'm on a 100Mbps plan)

    Bizarre.
    Richard7666
    Richard7666's Avatar
  5. Post 28th December 2018, 12:03 am
    #5
    Dynamix is legit, all my gear is from them. Sounds a bit odd, will be interesting to see if it reliably stays connected at 1Gb.
    Fragluton
    Fragluton's Avatar
  6. Post 28th December 2018, 3:51 pm
    #6
    Can you do some rapid pings to the router? When you say you only get 1mbit, is that to an internet speedtest server?
    JC
    JC's Avatar
  7. Post 10th January 2019, 10:59 pm
    #7
    Okay, update.

    It is slow when the *switch* is turned on if the PC is on first.

    ie, if I put the PC to sleep so as not to have to wait a long time to reopen a project, but have turned the network switch off overnight.

    No biggie, but weird.
    Last edited by Richard7666; 12th January 2019 at 1:20 pm.
    Richard7666
    Richard7666's Avatar
  8. Post 11th January 2019, 11:24 am
    #8
    Could it be a statically assigned IP conflict?
    JC
    JC's Avatar
  9. Post 12th January 2019, 1:21 pm
    #9
    JC wrote:
    Could it be a statically assigned IP conflict?
    Oooh, possibly. Static IPs are indeed set up on my two PCs, as the rendering software I use needs to know where to send jobs to.

    Although it's odd that my old 100/10 switch never had any issues on the same setup.
    Richard7666
    Richard7666's Avatar
  10. Post 12th January 2019, 3:42 pm
    #10
    I have a bunch of terminated Dynamix cables, I don't know who actually manufactures them. Was more so saying that in my experience they are good quality, so a cable issue would be odd.
    Fragluton
    Fragluton's Avatar
  11. Post 13th January 2019, 2:57 am
    #11
    Richard7666 wrote:
    Oooh, possibly. Static IPs are indeed set up on my two PCs, as the rendering software I use needs to know where to send jobs to.

    Although it's odd that my old 100/10 switch never had any issues on the same setup.
    Your current switch might be holding onto ARP entries a bit more vigourously which might explain it.. Dunno
    JC
    JC's Avatar